Built-in warming drawers and proofing drawers — one low-wattage element, one thermostat, and the first thing to fail in an otherwise healthy cooking stack.
Tell us the appliance and what it is doing. We will come and look.
Service for 16 major and premium appliance brands
The fault list changes with the format. A built-in column and a counter-depth machine fail in different places, and the one that has to come out of the cabinetry needs the extra pair of hands.
Under a wall oven or a cooktop
Holding at the wrong temperature, or not holding at all. A single element and a thermostat, which makes this one of the cheaper repairs in the kitchen.
Low heat with controlled humidity
Proofing runs far cooler than warming and depends on a water reservoir and a humidity setting. A drawer that proofs badly is usually the reservoir circuit.
Behind a cabinet front
The panel adds weight to a runner set for a bare drawer. Binding and a seal that no longer closes square follow from that, not from heat.
Rails, rollers and soft-close
The mechanical half fails more often than the heating half. Rails, rollers and the soft-close damper are all serviceable parts.
The compartment under the cavity
On a freestanding stove the drawer shares a cabinet with the oven above it, so a drawer fault sometimes traces back to the oven's board.
Set it and forget it, until it forgets
A drawer that runs hot or never reaches temperature is a sensor or a control, and both are inexpensive next to the cabinetry around them.
Every brand here builds warming drawers, and every card is about that machine. The parts we fit match the original specification.
Warming drawers built to sit in a run with the wall ovens, with a proper humidity setting rather than a single low heat.
Warming and proofing drawers designed to stack with the ovens, board-driven and built for a custom front.
Gourmet warming drawers with very fine low-range control and fault codes that read cleanly.
Heavy drawers on heavier runners, which is where the wear shows long before the element does.
Warming drawers on a widely serviced platform, so parts are available and the wait is short.
More control hardware than the category needs, which means an odd symptom is usually the board rather than the heat.
Warming drawers with electronics behind the fascia and a panel that changes how the runner behaves.
Warming drawers with the widest parts availability of the premium group — usually a same-visit repair.
We repair warming drawers from Bosch and Fisher & Paykel too — they are not the specialist end of the trade, and they are not priced like it.
Plenty of shops will turn up. These are the parts of the job that decide whether the repair actually holds.
Sub-Zero, Viking, Wolf and Thermador are built differently from mass-market machines, and they fail differently. These are the units our techs are on every day, so the fault gets recognized rather than hunted for.
Parts and labor are covered for up to twelve months depending on the repair, and the term is written on your invoice rather than left vague.
Parts that match the original specification. A cheaper substitute in a sealed system is how a one-visit repair becomes three.
The visit costs $99. Go ahead with the repair on that same visit and the fee comes off the bill, so the diagnosis is effectively free. Decide not to, and you have paid $99 for a straight answer and owe nothing further.
You see the price and approve it first. No work starts, and nothing is ordered, until you have said yes.
Most calls across the Valley get a technician out the same day, and anything leaking or unsafe goes to the front of the run.
BHGS #50900 for Major Appliance Repair, independently confirmed by Yelp. Fully insured, so a mistake in your kitchen is our problem and not yours.
Floors protected, the unit back on its rails, and the packaging gone with us. A built-in has to come out before most repairs can start.
From the first call to the final test, every step is built around your time and your kitchen.
Call or send the form. Brand, model if you have it, and what the appliance is actually doing — that is usually enough to know what to bring.
A technician finds the fault and explains it in plain terms, including the parts involved and what it will cost.
Written, flat, and agreed before any work begins. If you would rather not go ahead, that is fine — you pay the call-out and nothing more.
Most repairs finish on the first visit. The work and the parts are warrantied, and we check back that it held.
We cover 53 cities and neighborhoods, from the Conejo Valley to Long Beach.
We cover 53 cities and neighborhoods across Los Angeles and the Conejo Valley, from the Conejo Valley to Long Beach.
“This company is fantastic. Art worked tirelessly on my SubZero. We had multiple problems and he came out every time that I called him. They are reliable, honest, and quick. Thank you Art and Victor!”
“I am a property manager in LA County with multiple properties. MKH Appliance Repair is my go-to solution for all things appliance related. They have been helping me get repairs done quickly for the past 2-3 years. I cannot thank them enough for the quality service they provide! If you need your appliances fixed, call them!!…”
“… The Appliance Repairman arrived promptly and was incredibly professional and knowledgeable. He diagnosed the problem with my refrigerator quickly and explained the repair process clearly. The repair was done efficiently, and my appliance is now functioning perfectly. Their customer service was outstanding from start to finish.…”
The things people ask us most, answered plainly. If yours is not here, phone and ask.
(213) 523-3555Tell us the brand and what it is doing. Most repairs finish on the first visit, and you will know the price before any work starts.